€ 77.34
Sin Impuesto: € 63.92
Descripción
El sensor Z-Wave 3 en 1 está diseñado con tres sensores de detección:
1. Agua/ Inundación
2. Temperatura
3. Humedad
El detector puede ser utilizado como dispositivo de seguridad o como dispositivo domótico. Cuando el detector coopera con dispositivos de seguridad, el detector actúa como un dispositivo de seguridad detectando inundaciones, por ejemplo, junto a una lavadora con fugas. Además, la detección de alta temperatura y humedad puede definirse como disparador de señales de alarma.
Detalles Técnicos:
- Protocolo: Z-Wave Plus
- Frecuencia: 868,40 MHz
- Funciona con pilas: Batería de litio CR123A
- Alcance: Mínimo 40 metros en interiores, 100 metros en exteriores.
- Temperatura de funcionamiento: -10C grados ~ 40C grados; sólo para uso en interiores
Especificaciones
| Compatibilidad Controlador Principal | |
|---|---|
| eeDomus+ | not tested |
| Fibaro Home Center 2 v4.160 | partly compatible/unsecure only |
| Fibaro Home Center Lite v.4.160 | partly compatible/unsecure only |
| Vera Edge / Plus / Secure | fully compatible |
| Zipabox/Zipaminicro/ZipaTile | fully compatible |
| Piper / Piper NV (v.1.7.1) | not tested |
| Indigo | not tested |
| jeedom | not tested |
| Z-Wave.me / Z-Way / PoPP Hub v 3.2.1 | fully compatible |
| Domoticz | not tested |
| OpenHAB | not tested |
| ZiHome | not tested |
| Somfy Tahoma | not tested |
| Home Assistant | not tested |
| Telldus | not tested |
| Tech Data | |
| IP Rating | IP20 |
| Alimentación | CR123A lithium battery |
| FLiRS | CR123A lithium battery |
| Explorer Frames - NWI Support | Yes |
| SDK | 6.51.06 |
| App Version | SD3502 |
| Device Type | Notification Sensor |
| Z-Wave Alliance Product Link | https://products.z-wavealliance.org/products/1299 |
| S2 Security Frame | no |
| Procedimientos | |
| Inclusión | The device have auto inclusion function, if the device not add into Z-Wave network, after power up, it will into the auto inclusion (NWI) mode. In this mode, let the Z-Wave™ Controller entered inclusion mode, the device will added. The NWI mode will timeout in 30 seconds. After that you can pressing the tamper key three times within 1.5 seconds to manual inclusion with Z-Wave controller. After inclusion successful, the device will awake to receive the setting command from Z-Wave™ Controller about 20 seconds. |
| Exclusión | 1. Have Z-Wave™ Controller entered exclusion mode. 2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode. Node ID has been excluded. |
| Factory Reset | Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable. 1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th pressed, and the LED will light ON. 2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once. 3. IDs are excluded and all settings will reset to factory default. |
| Wake-up (despertar) | When the device power on, the device will wake about 20 seconds. In this duration, the controller can communicate with the device. Normally the device is always sleeping to save the battery energy. |
