€ 29.95
Sin Impuesto: € 24.75
Descripción
El mando a distancia Hank Z-Wave Plus es un dispositivo inalámbrico, portátil y recargable. Puede controlar dispositivos Z-Wave, como un enchufe inteligente o un atenuador inteligente después de ser incluido en un controlador Z-Wave. También puedes usarlo para activar escenas.
Este controlador de escenas puede realizar 3 acciones diferentes por botón, según el tipo de soporte: pulsación corta, soporte mantenido, soporte liberado. Al operar con una batería recargable con un rango de 3 a 6 meses, será muy fácil recargarla conectando un cable USB en su puerto micro-USB. ¡No es necesario cambiar las baterías! Además, este controlador de escenario está equipado con un zumbador que alertará cuando la batería esté baja (menos del 20%) o cuando la comunicación haya fallado. Un LED RGB está presente para brindar información visual. Este controlador de escenario también está equipado con la función de prueba de alcance Z-Wave. Se necesita un controlador Z-Wave (control remoto, dongle ...) para integrar este módulo en su red si ya tiene una red existente.
FUNCIONES:
- Controlador de escena Z-Wave +
- Controla hasta 3 dispositivos / escenas
- Función de prueba de alcance Z-Wave
- Batería recargable
- Advertencia de batería baja y error de comunicación (a través del zumbador)
- Seguridad de la comunicación por radio a través del cifrado AES-128
- Integra el chip de la serie Z-Wave 500 Actualizaciones de firmware por aire (OTA)
- Facilidad de uso e instalación
CARACTERÍSTICAS TÉCNICAS :
- Tipo de módulo: Transmisor de la serie Z-Wave + 500
- Fuente de alimentación: batería recargable 3,6V LIR2450
- Consumo de energía en espera: 3uA
- Consumo de energía en funcionamiento: 36mA
- Frecuencia: 868.42 Mhz
- Distancia de transmisión: 100 m en campo libre, 30 m en interiores
- Dimensiones: 50 x 50 x16 mm
- Temperatura de funcionamiento: 0 ° C a 40 ° C
- Certificaciones: FCC, CE,
- Z-Wave Número de certificación Z-Wave: ZC10-16095219
Manual:
Especificaciones
Compatibilidad Controlador Principal | |
---|---|
eeDomus+ | Full Compatible |
Fibaro Home Center 2 v4.160 | Not Tested |
Fibaro Home Center Lite v.4.160 | Not Tested |
Vera Edge / Plus / Secure | Not Tested |
Zipabox/Zipaminicro/ZipaTile | Not Tested |
Piper / Piper NV (v.1.7.1) | Not Tested |
Indigo | Not Tested |
jeedom | Full Compatible |
Z-Wave.me / Z-Way / PoPP Hub v 3.2.1 | Not Tested |
Domoticz | Not Tested |
ZiHome | Not Tested |
Somfy Tahoma | Not Tested |
Home Assistant | Not Tested |
Telldus | Not Tested |
Tech Data | |
IP Rating | IP20 |
Alimentación | Batterie rechargeable 3,6V LIR2450 |
FLiRS | No |
Explorer Frames - NWI Support | No |
SDK | 6.51.08 |
App Version | HW: 1 FW: 1.00 |
Device Type | Wall Controller |
Z-Wave Alliance Product Link | https://products.z-wavealliance.org/products/1968 |
Procedimientos | |
Inclusión | Included as non-secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Waave network controller operating manul). 3. Triple click a button. 4. If the inclusion is successful, the LED will blink in blue less than for 5 seconds and then keep on for 15 seconds. Included as a secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Wave network controller operating manual). 3. Pressing and holding a button for 3 seconds. 4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds. |
Exclusión | To remove the Scene Controller from the Z-Wave network: (1) Insert the LIR2450 battery. (2) Set the Z-Wave network main controller into remove mode (see Z-Wave controller operating manual). (3) Triple click the a button, if the exclusion is successful, LED will blink in orange for less than 5 seconds and then keep on for 3 seconds. |
Factory Reset | Pressing and holding a button for 20 seconds. Release the button after 20 seconds, LED will keep in yellow for 3 seconds. Scene Controller will be reset to factory defaults if you short press the button within this 3 seconds. Using this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
Wake-up (despertar) | Pressing and holding a button for 3 seconds. Led will turn to green, which means Scene Controller has been woken up. |