€ 34.99
Sin Impuesto: € 28.92
Descripción
La sirena de NeoCoolcam dota su casa inteligente con un factor de seguridad adicional. En conexión con otros dispositivos de su red Z-Wave, la sirena óptica visualmente atractiva alerta en diferentes situaciones. Ya sea que sea tan simple como alertarlo sobre una fuga de agua o escenarios más peligrosos como un incendio o un robo, esta sirena es lo suficientemente fuerte como para notificarle a usted y a sus vecinos sobre posibles peligros inminentes, dándole la oportunidad de responder rápidamente.
Además de usar la sirena para alarma, también se puede usar la sirena como timbre. La NeoCoolcam Siren reproduce 10 sonidos diferentes, que se pueden configurar mediante la configuración de parámetros o la clase de comando Indicador. Además, puede ajustar el volumen del sonido de la sirena y el sonido de la alarma en 3 etapas. En general, este dispositivo funciona específicamente bien para cualquier tipo de notificación acústica y óptica en su casa domotica.
La sirena a batería con un diseño de alta calidad armoniza con todas las áreas de la vivienda y se puede colocar donde desee
Caracteristicas:
- Tecnología inalámbrica: Z-Wave Plus
- Contenido de la caja: 1x NeoCoolcam Siren, 2x CR123 (batería de litio), elementos incluidos en el envio
- Sirena de alarma y timbre en un dispositivo
- Baterías: 2x CR123/ Duración de la batería: 1 año
- Alerta acústica (sirena) y óptica (LED rojo)
Manual:
Especificaciones
Compatibilidad Controlador Principal | |
---|---|
eeDomus+ | Full Compatible |
Fibaro Home Center 2 v4.160 | Full Compatible |
Fibaro Home Center Lite v.4.160 | Full Compatible |
Vera Edge / Plus / Secure | Full Compatible |
Zipabox/Zipaminicro/ZipaTile | Full Compatible |
Piper / Piper NV (v.1.7.1) | Full Compatible |
Indigo | Full Compatible |
jeedom | Full Compatible |
Z-Wave.me / Z-Way / PoPP Hub | Full Compatible |
Domoticz | Full Compatible |
ZiHome | Full Compatible |
Somfy Tahoma | Full Compatible |
Home Assistant | Full Compatible |
Telldus | Full Compatible |
Tech Data | |
IP Rating | IP20 |
Alimentación | 2x CR123 (Lithium battery) |
FLiRS | Yes |
Explorer Frames - NWI Support | Yes |
SDK | 6.51.09 |
App Version | HW: 48 FW: 2.90 |
Device Type | Siren |
Z-Wave Alliance Product Link | https://products.z-wavealliance.org/products/2171 |
Procedimientos | |
Inclusión | In the front casing, there is button that is used to carry out include, exclude or reset factory default settings on PCB Board. When power is first supplied, the LED will flash on and off alternately at one second intervals within 5 seconds if the detector has not been added a Z‐Wave network. Please get familiar with the terms below before starting the operations. This product can be included and operated in any Z‐Wave network with other Z‐Wave certified devices from other manufacturers and/or other applications. All non‐battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. |
Exclusión | 1. Remove the siren cover. 2. Make sure the siren is powered. 3. Set Z‐Wave controller or Z‐Wave gateway into inclusion mode (Refer to the controller or gateway operating manual) 4. Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off alternately five times. Note: If siren has not been added to Z‐wave network, the siren will enter inclusion mode automatically when it is powered on. You should let the controller enter into inclusion first before power on the siren in order to run this function. |
Factory Reset | Reset procedure will delete all information on the Z‐Wave network and Z‐Wave controller or Z‐Wave Gateway, and restore the siren to factory default settings. 1. Remove the device cover. 2. Make sure the siren is powered. 3. Press and hold the button for 10 seconds, led will blink once. 4. Release the button. Note: to use the reset procedure only when the primary controller is missing or inoperable. |
Wake-up (despertar) | You can press the button once to wake up the device and send wakeup notification to controller. If press successfully, the LED will blink one time |