€ 49.90
Sin Impuesto: € 41.24
Descripción
Mini enchufe para atenuadores está diseñado para controlar el encendido y apagado de la iluminación y equipos eléctricos en su hogar. También permite una función de regulación que sólo es compatible con las bombillas. Con una tensión de 220 - 240 V, este convertidor de conector puede soportar una carga de 11 W a 250 W.
Mini enchufe para atenuadores es un dispositivo compatible con Z-Wave ™ está diseñado para trabajar con todas las redes compatibles con Z-Wave ™. Puede ser controlado por un mando a distancia, software de PC o cualquier controlador Z-Wave en su red.
Advertencia: Este módulo tiene una salida de Alemán (SCHUKO). Para instalar correctamente en una decisión francesa, es necesario utilizar el adaptador LEGRAND LEG50382.
FUNCIONALIDADES:
- Ordenar la lámpara a distancia
- Módulo integrador tomada directamente de una toma de corriente y la carga que se desea controlar
- ON / OFF y la función Inversor para las luces de carretera
- El control de soporte local a través del botón integrado
- La tecnología de Z-Wave Más
- Dimensiones reducidas para pasar casi desapercibida
- LEDs de estado en el botón integrado
- función de repetidor Z-Wave
CARACTERÍSTICAS TÉCNICAS :
- Tipo de módulo: el receptor Z-Wave
- Potencia: 230 V, 50 Hz
- Consumo: 0.6W
- Potencia recomendada:
- carga resistiva <250W
- Bombilla de incandescencia: <250W
- Regulable bombilla LED: 6W a 250W
- Frecuencia: 868.42 MHz
- Rango: hasta 70 m en el exterior, de hasta 30 m en edificios
- Pantalla: LED en el botón
- dimensiones:
- Longitud (incluyendo conector): 74mm
- Diámetro: 52 mm
Especificaciones
Compatibilidad Controlador Principal | |
---|---|
eeDomus+ | Full Compatible |
Fibaro Home Center 2 v4.160 | Full Compatible |
Fibaro Home Center Lite v.4.160 | Full Compatible |
Vera Edge / Plus / Secure | Full Compatible |
Zipabox/Zipaminicro/ZipaTile | Full Compatible |
Piper / Piper NV (v.1.7.1) | |
Indigo | Full Compatible |
jeedom | Full Compatible |
Z-Wave.me / Z-Way / PoPP Hub v 3.2.1 | Full Compatible |
Domoticz | Full Compatible |
OpenHAB | Full Comaptible |
ZiHome | Full Compatible |
Tech Data | |
IP Rating | IP20 |
Alimentación | 230 V, 50 Hz |
Potencia de carga soportada | Carga Resistiva < 250 W Incandescente < 250 W Bombilla Led Dimmable: de 6w a 250 W |
Explorer Frames - NWI Support | Yes |
SDK | 6.51.02 |
App Version | |
Device Type | Light Dimmer Switch |
Peper1 Database link | |
Z-Wave Alliance Product Link | http://products.z-wavealliance.org/products/1527 |
Procedimientos | |
Inclusión | 1. Put the Z-Wave Controller into inclusion mode. 2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode. |
Exclusión | 1. Put the Z-Wave Controller into exclusion mode. 2. Press the link key three times within 1.5 seconds to put the unit into exclusion mode. |
Factory Reset | 1. Press the link key three times within 1.5 seconds to put the unit into exclusion mode. 2. Within 1 second of step 1, press link key again and hold it until LED is off (about 5 seconds). 3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes. 4. Use this procedure only in the event that the network primary controller is missing, or otherwise inoperable |